| FOR
THOSE WHO DEMAND THE BEST IN POWER and
PERFORMANCE |
| Print
Product Brochure |
|
Century's
1040s (40 ton) and 1060S (60 ton) Rotators have set the industry
standard for superior design and performance in heavy duty
recovery equipment for years. Based on that same past
knowledge and experience the new 1075S is bringing the rotator
market to a whole new level. The Century 1075S, 75 Ton
Rotator, is outfitted with 60,000 lb. planetary 2-speed winches,
newly designed winch buckets, and increased boom reach to tackle
the toughest recovery applications.
For supreme stability in a variety of situations Century's
Rotators are equipped with a hydraulic stabilization system that
includes front hydraulic outriggers with over 17' of spread and
rear patented outriggers designed for stability, in lifting as
well as anchoring your unit during those tough recoveries.
|
|
STANDARD
BODY FEATURES |
| 96"
Wide Aluminum Modular Body |
180"
C.B. |
| Large
Forward Compartments |
Compartments
Over the Wheel Well |
| Push
to Open/Push to Close Latches |
Door
Checks |
| Power
Toolbox Compartment Locks |
LED
Federal #108 Lighting |
| LED
Toolbox Lighting |
Rubber
Fenderettes |
| Mud
Flaps |
Side
Worklights |
| Chain
Rack |
Fork
Holders |
| Attachment
Storage |
Rubber
Isolators |
| Enclosed
Inner Wheel Wells |
Rigid
Torsional Resistant Mounting Frame |
| Tailboard
Mounted D-Rings |
Two
Rear Outrigger Spade Attachments |
|
STANDARD
BOOM FEATURES |
| Power
Elevation |
360°
Continuous Boom Rotation |
Proportional
2 Stage Power Boom
Extension with Counter Balance Valve |
Hydraulic
Reservoir with an Oil Level Sight
Gauge, Tank Drain, and Enlarged Access
Panel |
| Nylatron
Boom Slide Pads |
Holding
Valves for Boom Elevation &
Extension |
| Dual
2-Speed Winches |
Cable
Tensioners |
| Winch
Air Free Spool |
Boom
Angle Indicator |
3-Stage
Hydraulic Rear Outriggers with
Removable Pads |
Air
Activated House Lock, Secures Boom for
Transport in Rear or Forward Position |
| Hydraulic
Front Outriggers (Over Frame) |
House
Lock Indicator |
| Hydraulic
Pump |
360°
Sheave Heads |
| Dual
Control Stations |
Hydraulic
Pressure Gauges (Driver Side) |
Power
Pal System, 8 Function Hand Held
Lanyard and 9 Function Floor Mounted
Switch Panel |
2
"D" Rings Mounted on 1st and 3rd Stage |
|
STANDARD
UNDERLIFT FEATURES |
| Power
Elevation |
Power
Extension |
| Power
Tilt |
Hydraulic
Fold |
| 3-Stage
Design |
2
Piece Pivot Pin |
| Upper/Lower
Thrust Washer |
Low
Profile Crossbar |
| 70°
Pivoting Crossbar |
Low
Profile Fork Holders |
| 8
Pairs of Cast Steel Forks |
1
Pair of Spring Lift Adapters |
| 1
Pair of Hook Adapters |
Safety
Chains in Tailboard |
|
OPTIONAL
EQUIPMENT |
| Additional
Lift Forks |
Low
Pull "D" Ring Kit |
212"
2-Stage or 262" 3-Stage Under
Frame "H-Beam" Front Outriggers |
22"
Rear Outrigger Extension
(For 3-Stage Rear Outriggers) |
| Front
Outrigger Side Pull Attachment |
Chain
Package |
| Endless
Loop Sling Package |
Recovery
Straps |
| Snatch
Blocks |
Light
Bar |
| Snatch
Block Storage Rack |
25,000
lb. XHD Tire Lift * |
| 25,000
lb. XHD Crossbar |
Strobe
Kits |
| Halogen
Work & Hook-Up Lighting |
Xenon
Boom Lights |
| Wide
Load Light Bar |
Lowrider
Underlift |
| Rear
Camera & Monitor |
Engine
Data Information Center |
| Aluminum
Dress-Up Kits |
Power
Touch System - Includes 15-Function
Wired and Wireless Controls, In-Cab Underlift
Control, and Front & Rear Function Switch
Panels |
| Rear
Air & Electrical Hook-ups |
Navigation
System |
| 2nd
Stage "D" Rings (Std. on the 1075S) |
Side
Mounted "D" Rings
(Top Frame Front Outriggers) |
| Single
or Dual Drag Winches |
Cam-locks
for "D" Ring Hold-Back |
Radio
Proportional Controls with Dual
Manual Controls |
Radio
Proportional Controls with Single
Manual Controls (Drivers Side) |
| Air
Shift PTO |
House
Lock Window (Driver Side) |
| Tailboard
Underlift Controls |
Manual
Override Control for PTO |
| Convenience
Group (Rails & Steps) |
24",
30", 36", or 48" Tunnel Saddle Box |
Winch
Bucket Mounted Aluminum
Tubular Pylon |
Shelf
Kit for 36" or 48" Tunnel Saddle Box |
| 3-Drawer
Toolbox |
4-Drawer
Toolbox |
| Folding
Wash-down Sink |
Fork
Riser Brackets |
| Offset
Fork Holder Extension |
Pintle
Hook Attachment |
5th
Wheel Plate
(Requires Pintle Hook Attachment) |
Trailer
Ball Adaptor
(Requires Pintle Hook Attachment) |
| Chain
Hook Slide Adapter |
Tailboard
Cable Tiebacks |
| Heavy
Duty Tire Lift |
Additional
Lighting |
| Installation |
Print
Product Brochure |
| *
Requires XHD Crossbar |
|
|
BOOM
SPECIFICATIONS |
| 1040S |
|
| Boom
Structural Rating (S.A.E.) |
Retracted
30° |
Extended
30° |
| |
80,000
lbs. |
25,000
lbs. |
| Maximum
Angle |
55° |
| Maximum
Hook Height |
352" |
Reach
Past Tailboard at
Minimum Boom Angle |
156" |
| 1060S |
|
| Boom
Structural Rating (S.A.E.) |
Retracted
30° |
Extended
30° |
| |
120,000
lbs. |
24,000
lbs. |
| Maximum
Angle |
60° |
| Maximum
Hook Height (inches) |
449" |
Reach
Past Tailboard at 30°
Boom Angle (inches) |
249" |
| 1075S
/ 1075S2 |
|
| Boom
Structural Rating (S.A.E.) |
Retracted
30° |
Extended
30° |
| |
150,000
lbs. |
36,000
lbs. |
| Maximum
Angle |
60° |
| Maximum
Hook Height |
485" |
Reach
Past Tailboard at
Minimum Boom Angle |
292" |
|
WINCH
SPECIFICATIONS |
| 1040S |
| Winch
Capacity |
(
2) 35,000 lbs. |
| Winch
Type |
Planetary
2-Speed |
| Cable
Specifications |
3/4"
x 200' 6x37
I.W.R.C. |
| Air
Cable Tensioners |
Standard |
| Air
Winch Clutch Release |
Standard |
| 1060S |
| Winch
Capacity |
(2)
50,000 lbs. |
| Winch
Type |
Planetary
2-Speed |
| Cable
Specifications |
3/4"
x 250' 6x37
I.W.R.C. |
| Air
Cable Tensioners |
Standard |
| Air
Winch Clutch Release |
Standard |
| 1075S |
| Winch
Capacity |
(2)
60,000 lbs. |
| Winch
Type |
Planetary
2-Speed |
| Cable
Specifications |
7/8"
x 250' 6x37
I.W.R.C. |
| Air
Cable Tensioners |
Standard |
| Air
Winch Clutch Release |
Standard |
| 1075S2 |
| Winch
Capacity |
(2)
50,000 lbs. |
| Winch
Type |
Planetary
2-Speed |
| Cable
Specifications |
3/4"
x 250' 6x37
I.W.R.C. |
| Air
Cable Tensioners |
Standard |
| Air
Winch Clutch Release |
Standard |
| 1060S |
Print
Product Brochure |
|
|
|
|
| 1075S
/ 1075S2 |
Print
Product Brochure |
|
|
| |
|
|
| |
|
UNDERLIFT
SPECIFICATIONS |
| SDU-4 |
Capacity
Fully Extended
to C.L. of Forks |
17,000
lbs. @ 143.5" |
Capacity
Fully Retracted
to C.L. of Forks |
55,000
lbs. @ 54" |
| Underlift
Tilt |
10°
+ 10° - |
| Lowrider |
Capacity
Fully Extended
to C.L. of Forks |
18,000
lbs. @ 165.5" |
Capacity
Fully Retracted
to C.L. of Forks |
55,000
lbs. @ 66" |
| Underlift
Tilt |
10°
+ 7° - |
Print
Product Brochure
|
| SDU-4 |
|
|
| |
| CHASSIS
RECOMMENDATION |
| ALL
MODELS |
| Front
Axle (lbs.) |
20,000 |
| Rear
Axle (lbs.) |
46,000 |
| Clear
C.A. / C.B. |
180" |
| After
Frame from Center of Rear Axle |
40" |
| R.B.M.
(in./lbs.) |
4,000,000 |
|
*All
recommendations are minimums. Heavier specifications may
be required depending on chassis and equipment weight. The
outside frame rails of chassis extending behind the cab must be
free of fuel tanks, air tanks, battery boxes, etc. A
tandem chassis may be used but a tri-axle is recommend for
rotator applications. Maximum frame height for units
equipped with the SDU-4 underlift is 42". Always
consult your local distributor or the factory for additional
information.
|
|
All ratings are based on structural factors only, not
vehicle capacities or capabilities. Specifications shown
are approximations and may vary depending on chassis selected. Miller
Industries Towing Equipment Inc. reserves the right to change or
modify product and or specifications without notice or
obligation. Some equipment shown is optional.
|
