| FOR
THOSE WHO DEMAND THE BEST IN POWER and
PERFORMANCE |
| Click
here to view this product's brochure |
|
Century's
1060 has set the industry standard for superior design and
performance in the heavy duty, non-integrated, recovery
equipment. The 1060 2-Stage and 3-stage is ideal for the
professional tower who prefers a fixed recovery boom with an
independent underlift. Century offers the 1060 in a 2-Stage
and 3-Stage configuration, each of which is available with
tandem or tri-axle tool compartments. Century, for those who
demand the best in
power and performance.
|
|
STANDARD
BODY FEATURES |
| 96"
Wide Aluminum Modular Body |
180"
C.B. |
| Large
Forward Compartments |
Compartments
Over the Wheel Well |
| Double
Panel Doors |
Door
Checks |
| Double
Action Latches with Keys |
Federal
#108 Lighting |
| Toolbox
Lighting |
Rubber
Fenderettes |
| Mud
Flaps |
Side
Worklights |
| Chain
Rack |
Fork
Holders |
| Attachment
Storage |
Rubber
Isolators |
| Enclosed
Inner Wheel Wells |
Rigid
Torsional Resistant Mounting Frame |
| Tailboard
Mounted D-Rings |
|
|
STANDARD
BOOM FEATURES |
| Power
Elevation |
Hydraulic
Reservoir with an Oil Level Sight
Gauge, Tank Drain, and Enlarged Access
Panel |
| Nylatron
Boom Slide Pads |
Holding
Valves for Boom Elevation & Extension |
| Dual
2-Speed Winches |
Cable
Tensioners |
| Winch
Air Free Spool |
Hydraulic
Rear Outriggers with Flipper Feet |
| Hydraulic
Pump |
360°
Sheave Heads |
| Dual
Control Stations |
Power
Pal System, 8 Function Hand Held
Lanyard and 9 Function Floor Mounted
Switch Panel |
| Hydraulic
Pressure Gauges (Driver Side) |
2
"D" Rings Mounted on Inner and Outer Boom |
|
STANDARD
UNDERLIFT FEATURES |
| Power
Elevation |
Power
Extension |
| Power
Tilt |
Hydraulic
Fold |
| 3-Stage
Design |
2
Piece Pivot Pin |
| Upper/Lower
Thrust Washer |
Low
Profile Crossbar |
| 70°
Pivoting Crossbar |
Low
Profile Fork Holders |
| 8
Pairs of Cast Steel Forks |
1
Pair of Spring Lift Adapters |
| 1
Pair of Hook Adapters |
Safety
Chains in Tailboard |
|
OPTIONAL
EQUIPMENT |
| Additional
Lift Forks |
Low
Pull "D" Ring Kit |
| Extension
Storage Compartment |
Chain
Package |
| Endless
Loop Sling Package |
Recovery
Straps |
| Snatch
Blocks |
Light
Bar |
| Snatch
Block Storage Rack |
Super
Duty Tire Lift - 25,000 lb. Capacity
with 25,000 lb. Crossbar |
| 25,000
lb. Crossbar |
Strobe
Kits |
| Xenon
Boom Lights |
Halogen
Work & Hook-Up Lighting |
| Wide
Load Light Bar |
Low
Rider Underlift |
| Rear
Camera & Monitor |
Engine
Data Information Center |
| Installation |
Navigation
System |
| Rear
Air & Electrical Hook-Ups |
Power
Touch System - Includes 15-Function
Wired and Wireless Controls, In-Cab Underlift
Control, and Front & Rear Function Switch
Panels |
| Air
Shift PTO |
Single
or Dual Drag Winches
(Except XLT Series) |
| Tailboard
Underlift Controls |
Manual
Override Control for PTO |
| Convenience
Group (Rails & Steps) |
24",
30", 36", or 48" Tunnel Saddle Box |
| Offset
Fork Holder Extension |
Aluminum
Dress-Up Kits |
| 3-Drawer
Toolbox |
7-Drawer
Toolbox |
| Chain
Hook Slide Adapter |
Folding
Wash-down Sink |
| Heavy
Duty Tire Lift |
Fork
Riser Brackets |
| Tailboard
Cable Tiebacks |
Pintle
Hook Attachment |
5th
Wheel Plate
(Requires Pintle Hook Attachment) |
Trailer
Ball Adaptor
(Requires Pintle Hook Attachment) |
| Additional
Lighting |
|
|
BOOM
SPECIFICATIONS |
| 1060
2-Stage |
| |
Retracted
30° |
Extended
30° |
| Boom
Structural Rating (S.A.E.) |
120,000
lbs. |
35,000
lbs. |
| Maximum
Angle |
60°
|
| Maximum
Hook Height (inches) |
362" |
Reach
Past Tailboard at 30°
Boom Angle (inches) |
170" |
| 1060
3-Stage |
|
| Boom
Structural Rating (S.A.E.) |
Retracted
30° |
Extended
30° |
| |
120,000
lbs. |
24,000
lbs. |
| Maximum
Angle |
60° |
| Maximum
Hook Height (inches) |
433" |
Reach
Past Tailboard at 30°
Boom Angle (inches) |
253" |
|
WINCH
SPECIFICATIONS |
| Winch
Capacity |
(2)
50,000 lbs. |
| Winch
Type |
Planetary
2-Speed |
| Cable
Specifications |
3/4"
x 250' 6x37
I.W.R.C. |
| Air
Cable Tensioners |
Standard |
| Air
Winch Clutch Release |
Standard |
| 1060
- 2 Stage |
|
|
| 1060
- 3 Stage |
|
|
| |
|
UNDERLIFT
SPECIFICATIONS |
| SDU-4 |
Capacity
Fully Extended
to C.L. of Forks |
17,000
lbs. @ 132" |
Capacity
Fully Retracted
to C.L. of Forks |
55,000
lbs. @ 54" |
| Underlift
Tilt |
10°
+ 10° - |
| Low
Rider |
Capacity
Fully Extended
to C.L. of Forks |
18,000
lbs. @ 165" |
Capacity
Fully Retracted
to C.L. of Forks |
55,000
lbs. @ 66" |
| Underlift
Tilt |
10°
+ 7° - |
|
| SDU-4 |
|
|
| |
|
CHASSIS
RECOMMENDATION |
| ALL
MODELS |
| Front
Axle (lbs.) |
20,000 |
| Rear
Axle (lbs.) |
46,000 |
| Clear
C.A. / C.B. |
180" |
| After
Frame from Center of Rear Axle |
40" |
| R.B.M.
(in./lbs.) |
3,500,000 |
|
*All
recommendations are minimums. Heavier specifications may be
required depending on chassis and equipment weight. The
outside frame rails of chassis extending behind the cab must be
free of fuel tanks, air tanks, battery boxes, etc. A
tandem chassis may be used but a tri-axle is recommend for rotator
applications. Maximum frame height for units equipped with
the SDU-4 underlift is 42". Always consult your local
distributor or the factory for additional information.
|
|
All ratings are based on structural factors only, not
vehicle capacities or capabilities. Specifications shown are
approximations and may vary depending on chassis selected. Miller
Industries Towing Equipment Inc. reserves the right to change or
modify product and or specifications without notice or
obligation. Some equipment shown is optional.
|
